軋漿輥英語怎麼說及英文單詞

⑴ 色漿的英語單詞是什麼

從用途上來分
調色機用的色漿叫做：colorants
工廠，車間人工用色漿叫做：Dispersions，即顏料分散體的意思

⑵ 形容東西一閃一閃 bulinbulin的 英文單詞是什麼，英譯中文的詞是什麼

形容東西一閃一閃的英文單詞，譯為閃亮的，發光的。

讀音：英['ʃaɪni]美['ʃaɪni]

其原形為shine，shine的基本意思是「照耀」「發光」,指太陽、燈等發光體發出光亮,也可指物體反射出光亮,還可指用手電筒等的光向某方向照射。引申可作「表現突出,出眾」解。其過去式和過去分詞都是shone。

在美式英語中shine還可作「擦」解,表示把某物擦亮、磨光或使之發亮,其過去式和過去分詞都是shined,不是shone。

shine作「發光」解時是不及物動詞,作「擦亮」解時是及物動詞。用作及物動詞時接名詞或代詞作賓語。

例句：

I am amazed to see a beggar step into a shiny Mercedes.

看到一個乞丐跨進一輛閃亮的賓士轎車我驚愕不已。

The genie gave her a big, shiny ruby.

精靈給她一顆又大又閃亮的紅寶石。

(2)軋漿輥英語怎麼說及英文單詞擴展閱讀：

shine, light up兩者都有「發光」「照亮」的意思。其區別在於:

1、shine是不及物動詞,指太陽等能發亮的主體自身發光; 而light up則是及物動詞,意思是「照亮…」。例如:

The sun shines bright in my old Kentucky home.

明媚的陽光照耀著我古老的肯塔基故鄉。

All the streets were lit up with electricity.

所有街道上燈火通明。

2、shine和light up均可用於比喻,指「眼睛亮」,但前者強調狀態,後者強調由不亮到亮的變化。例如:

Her eyes shone with pleasure.

她的眼睛裡閃爍著愉快的光芒。

Her eyes lit up when I mentioned a holi- day.

當我提到去度假時,她的雙眼頓時亮了起來。

⑶ 輥道的英語翻譯 輥道用英語怎麼說

輥道是在軋機上往復軋制及軋後輸送到精整工序等的設備，應該是在一個平台（table）上工作，所以可翻譯為 rollers table，其工作的路徑是 roller-way。

⑷ 處理單詞用英語怎麼說

處理
[詞典來] handle; manage; deal with; dispose;
[例句]對她身源上的傷口和淤傷進行了處理和治療。
She was treated for cuts and bruises.

⑸ 請教軋輥磨床相關專業英語詞彙

工件床身來 Workpiece lathe bed
砂輪床身 Grinding Wheel lathe bed
砂輪主軸源 grinding ore wheelspindle
頭架 head frame
尾架 tail stand
中心架 center rest
磨架 grinding frame
軋輥軟著陸裝置 roller soft landing device
測量系統 measurement system
曲線磨削系統 curve grinding system the
主軸精壓系統 main axle fine pressure system

真不簡單，盡量找了~

⑹ 求軋輥使用說明書，英文版的。

Mill rolls operating manual
1. Roll should prevent any damage ring transportation.
2. Roll should be stored in a dry, ventilated room to avoid damp，surface should be covered with rust preventive oil.
3. Before using, should wipe the oil, dirt and rust on surface and then doing conventional inspection, especially carefully check the roll body and roll neck surface in case of defects like nick, indentation, pitting, and crack. Those defective rolls are not allowed to use.
4. Before going into use roll quality card shall be established, register roll number, specification, size and related inspection results, then filed those original records.
5. Installation should be careful enough to avoid scratch or bruising on roll surface.
6. Quality of bloom should be carefully checked before rolling, rolling process operation should be strictly obeyed while rolling in order to avoid overload rolling.
7. The hot roll can not accumulate on the wet and cold ground, collision between rolls should be avoided.
8. Establish a roll change grinding system, allocate reasonable roll change cycle, matched with corresponding nondestructive test method (bow wave, magnetic powder, ultrasonic etc), complementary with hardness testing to decide reasonable grinding quantity and grinding process.
9. During grinding on work roll, every time the minimum quantity should grind off the tired layer, the layer depth is usually of 0.15-0.30 mm.
After worked times later support roll need to clean the burr and tired layer thoroughly (the layer depth is usually of 2-5mm), to prevent flaking and make corresponding truing of roll body chamfering.
During roll grinding, should also pay attention to the difference of matching roll』s diameter to meet the design requirements.
10. While installed new roll (including new grinded roll, roll disuse for a period), it should be preheated while rolling with rapid speed, bandwidth and large rolling rection.
11. The grinded roll need to guard against rust, and prohibited to place on the ground.
12. Record the grinding quantity after each grinding, the rolling steel NO., specifications, rolling quantity, grinding reason (such as normal roll change, different specifications roll change, scratch, peel, sticky steel, crack, etc.).
Should select the roll with fitted hardness, convexity and roughness according to rolling material, using frequency, rolling rection, rolling speed etc.. The principle to use roll is: the new (high hardness) roll is suitable for broadband and thin belt finishing rolling; Old (low hardness) roll applies to the thick and narrowband beginning rolling. Roll must implement the principle of extension, avoid misuse and blend. Finishing roll can not be used as roughing roll.
Roll neck need have good lubrication and cool-off, prevent overheating to damage the surface. Check mechanical components, prevent the roll』 abnormal invalidation caused by accidents of equipment.
While rolling roll should be cool-off and lubricating enough, prevent the decline of hardness and crack caused by overheating.
Rolling should be clean, prevent deflection, folded or mixed with something wrong, prevent corrosion procts embedded into metal.
Regular maintenance, inspection and monitoring to avoid taking "disease" equipment operation、over-term service. Pay attention about shock, ensure roll working in a good condition.

⑺ 英語單詞橡皮怎麼說

rubber音標：英 [ˈrʌbə(r)] 美 [ˈrʌbər]

釋義：

1、n.橡膠;橡皮;黑板擦;(某些紙牌游戲或體育運動中相同的對手或隊伍間)多輪決勝負的比賽

Ifplasticandrubberareburnt,they'llgiveoffpoisonousgases.

要是塑料和橡膠被焚，就會放出有毒的氣體。

2、adj.橡膠製成的

.

早期汽車的輪胎是用鐵實心橡膠製成的。

相關短語：

1、crude rubber 天然橡膠,未加工橡膠,粗橡膠

2、impoverished rubber 失去彈性的橡皮

3、natural rubber 天然橡膠

4、raw rubber 生膠

5、synthetic rubber 人造橡膠,合成橡膠

(7)軋漿輥英語怎麼說及英文單詞擴展閱讀：

復數： rubbers

派生詞： rubber adj.

詞語用法：

n. (名詞)

1、 rubber的基本意思是「橡膠」,也可指「合成橡膠」,是物質名詞,不可數。

2、 rubber也可轉變為個體名詞而表示擦鉛筆或墨水痕跡的「橡皮」,多用在英式英語里,在美國作eraser,是可數名詞。

3、 rubber還可作「黑板擦」解,是可數名詞。

4、 rubber的復數形式rubbers可作「橡膠套鞋」解。

⑻ 軋線軋輥用英語怎麼說

軋線軋輥
Rolled roll
軋輥roller; roll; bowl; mill roll